{"product_id":"clicky-clack-door-panel-retainer-2-meter-rubber-seal-for-ccd-trident-2-4-and-2020-extrusions","title":"Rubber Panel Retainer Seal for Clicky Clack Door Trident \/ 2.4 and 2020 Extrusions","description":"\u003ch2\u003e2 Meters for Voron 2.4 \u0026amp; Trident (2020 Extrusions)\u003c\/h2\u003e\n\u003cp\u003eIf you're building or upgrading a Clicky Clack Door (CCD) on your Voron 2.4 or Voron Trident, this is the rubber seal you need. This 2-meter strip sits inside the slot of your 2020 aluminum extrusions and grips the edges of your acrylic panel — holding it firmly in place while creating a cleaner, tighter door assembly.\u003c\/p\u003e\n\u003cp\u003eOne 2-meter length is enough to go around all four sides of a standard Clicky Clack Door frame. It's the same panel retainer called out in the official CCD BOM, so there's no guesswork — just cut, fit, and done.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eWhat Does This Rubber Seal Actually Do?\u003c\/h3\u003e\n\u003cp\u003eThink of it like the rubber trim inside a car door — it fills the gap between the metal frame and the glass. In your Voron door, it fills the slot of the 2020 extrusion and squeezes around the edge of your acrylic panel. This does two things:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHolds the panel in place\u003c\/strong\u003e — no rattling, no shifting, no loose acrylic.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCreates a tighter seal\u003c\/strong\u003e — improves chamber enclosure, which helps when printing ABS, ASA, Nylon, or any filament that needs heat retention.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003ePrinter\u003c\/th\u003e\n\u003cth\u003eCompatible?\u003c\/th\u003e\n\u003cth\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoron 2.4 (all sizes)\u003c\/td\u003e\n\u003ctd\u003e✅ Yes\u003c\/td\u003e\n\u003ctd\u003eStandard CCD BOM spec\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoron Trident (all sizes)\u003c\/td\u003e\n\u003ctd\u003e✅ Yes\u003c\/td\u003e\n\u003ctd\u003eStandard CCD BOM spec\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAny build using 2020 extrusions\u003c\/td\u003e\n\u003ctd\u003e✅ Yes\u003c\/td\u003e\n\u003ctd\u003ePanel must fit the extrusion slot\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePanels thinner than 3mm (US acrylic)\u003c\/td\u003e\n\u003ctd\u003e⚠️ May need adjustment\u003c\/td\u003e\n\u003ctd\u003ePrint wedge shims or adjust panel sizing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003eSpecs\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eLength\u003c\/td\u003e\n\u003ctd\u003e2 meters (1 piece, cut to length)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eExtrusion compatibility\u003c\/td\u003e\n\u003ctd\u003e2020 aluminum extrusion (standard slot)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eColor\u003c\/td\u003e\n\u003ctd\u003eBlack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaterial\u003c\/td\u003e\n\u003ctd\u003eRubber (flexible, compressible)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTypical panel thickness\u003c\/td\u003e\n\u003ctd\u003e3mm acrylic (US standard)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eQuantity\u003c\/td\u003e\n\u003ctd\u003e1 strip (sufficient for one full door frame)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003eHow to Install — Quick Overview\u003c\/h3\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cstrong\u003eCut four lengths\u003c\/strong\u003e — measure each side of your door frame. Cut corners at a 45° miter angle for clean joints. Print the community miter guide if you want precise cuts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePush the seal onto the panel edges first\u003c\/strong\u003e — slide each strip onto the edge of the acrylic before assembling the extrusions. This is much easier than inserting the seal after the frame is built.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSlide the extrusions onto the seal\u003c\/strong\u003e — the shorter extrusions go on first, then the longer ones. The seal fits snugly, so work one end at a time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDon't over-insert\u003c\/strong\u003e — once a section of seal is in the extrusion slot, it won't slide easily. Start from one end and work your way down.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e⚠️ \u003cstrong\u003ePro tip from the community:\u003c\/strong\u003e If your panel is thinner than 3mm, print small wedge shims to push the panel forward so it presses firmly against the seal. This ensures a proper hold with no play.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eWho Is This For?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoron 2.4 or Trident builders\u003c\/strong\u003e installing the Clicky Clack Door mod for the first time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoron owners replacing a worn or damaged panel retainer\u003c\/strong\u003e — the seal does compress over time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAnyone printing ABS, ASA, or Nylon\u003c\/strong\u003e who wants a tighter chamber seal to hold heat and reduce warping.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilders using 2020 extrusions\u003c\/strong\u003e in any custom enclosure build that needs a clean, flexible panel retainer.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e2 meters. One door. No more loose panels.\u003c\/p\u003e","brand":"West3D 3D Printing Supplies","offers":[{"title":"Default Title","offer_id":52735670452518,"sku":"LDO1637","price":5.99,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1004\/1986\/2822\/files\/clicky-clack-door-panel-retainer-2-meter-rubber-seal-for-ccd-trident-24-and-2020-extrusions-west3d-3d-printing-supplies-ldo-motors-511198.jpg?v=1773259449","url":"https:\/\/supplies3d.shop\/products\/clicky-clack-door-panel-retainer-2-meter-rubber-seal-for-ccd-trident-2-4-and-2020-extrusions","provider":"SUPPLIES3D","version":"1.0","type":"link"}