{"product_id":"32-x-1kg-high-speed-petg-filament-pack-1","title":"High Speed PETG Filament 32-Pack","description":"\u003ch2\u003e32kg at $13.49\/kg | 43% Off | Mix Any 32 Colors, Free USA Shipping\u003c\/h2\u003e\n\u003cp\u003eThirty-two kilograms of High Speed PETG. Any 32 colors from our full range. Vacuum-sealed per spool. Free shipping across the USA. At $13.49\/kg — 43% off individual pricing — this is supplies3d's largest filament pack, built for print farms, workshops, and production makers who can't afford to run out or reorder every week.\u003c\/p\u003e\n\u003cp\u003ePETG hits the sweet spot that most functional printing demands: tougher and more heat-resistant than PLA, dramatically easier to print than ABS, and chemically resistant enough for parts that live outdoors or near moisture. The High Speed formulation extends that profile to faster printers — supporting speeds up to 300mm\/s on properly tuned setups without sacrificing layer adhesion or surface quality.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003ePETG in Plain Language — What It Actually Does\u003c\/h3\u003e\n\u003cp\u003eImagine a water bottle. It's made of PET — the same base polymer as PETG. It flexes without cracking, survives a drop, handles hot liquid without warping, and doesn't absorb moisture or rust. PETG (the \"G\" stands for glycol-modified) takes those same properties and makes them printable. The result is a filament that:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDoesn't shatter on impact\u003c\/strong\u003e — PLA is rigid but brittle under sudden force. PETG bends slightly and absorbs the hit. Better for enclosures, brackets, and anything that might get knocked around.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSurvives heat up to ~80–85°C\u003c\/strong\u003e — PLA starts deforming around 60°C (hot car interior, near electronics, direct summer sun). PETG stays rigid well above that threshold.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eResists moisture and UV\u003c\/strong\u003e — suitable for outdoor parts, garden fixtures, signage, and anything that lives in a humid or sun-exposed environment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDoesn't warp like ABS\u003c\/strong\u003e — no enclosure required. PETG has very low shrinkage during cooling, which means large flat parts stay flat without the thermal management that ABS demands.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003ePack Contents \u0026amp; Value Breakdown\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePack size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e32 × 1kg spools (32kg total \/ 70.4 lbs)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaterial\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eHigh Speed PETG\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFilament diameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.75mm ±0.02mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eColor selection\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eChoose any 32 colors from our full PETG range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrice per kg\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e$13.49 (43% off individual spool pricing)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePackaging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eVacuum-sealed with desiccant — each spool individually sealed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFree across the USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003eHigh Speed PETG — What \"High Speed\" Actually Means\u003c\/h3\u003e\n\u003cp\u003eStandard PETG tops out at around 50–60mm\/s before you start seeing stringing, under-extrusion, or surface quality issues. High Speed PETG is reformulated to maintain consistent melt flow and layer adhesion at significantly higher speeds. On a well-tuned direct drive setup with adequate cooling, speeds of up to 300mm\/s are achievable — without the stringing or bonding problems that plagued older PETG formulations at speed.\u003c\/p\u003e\n\u003cp\u003eThat matters for print farms. The difference between 50mm\/s and 150mm\/s on a run of 50 identical parts is hours of machine time per day. At 32kg, this pack is priced to make that math work.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003ePrint Settings for High Speed PETG\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSetting\u003c\/th\u003e\n\u003cth\u003eRecommended Range\u003c\/th\u003e\n\u003cth\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eNozzle temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e230–260°C\u003c\/td\u003e\n\u003ctd\u003eStart at 240°C. Raise 5°C if layers aren't bonding. Lower 5°C if you see stringing or surface blobs.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBed temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e70–90°C\u003c\/td\u003e\n\u003ctd\u003e85°C is the universal starting point. Drop to 80°C if prints bond too aggressively. Let bed cool to room temp before removing prints — never pull PETG off a hot bed.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEnclosure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eNot required\u003c\/td\u003e\n\u003ctd\u003ePETG doesn't warp like ABS. Open-frame printers work fine. For very large parts, an enclosure reduces thermal stress.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart cooling fan\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20–60%\u003c\/td\u003e\n\u003ctd\u003eMore fan = less stringing, better overhangs. Less fan = stronger layer bonding. Start at 40% and tune from there.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrint speed — standard\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e40–60mm\/s\u003c\/td\u003e\n\u003ctd\u003eSafe range for any FDM printer. Reliable quality across all geometries.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrint speed — high speed\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eUp to 300mm\/s\u003c\/td\u003e\n\u003ctd\u003eRequires direct drive, high-flow hotend, and adequate part cooling. Dial up gradually — don't jump straight to max speed.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFirst layer speed\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e20–30mm\/s\u003c\/td\u003e\n\u003ctd\u003eAlways slow down the first layer regardless of print speed profile.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRetraction — Direct Drive\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1–3mm at 20–30mm\/s\u003c\/td\u003e\n\u003ctd\u003ePETG needs less retraction than most materials. Too much retraction causes grinding and clogs. Start low and increase only if stringing persists.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRetraction — Bowden\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3–7mm at 40mm\/s\u003c\/td\u003e\n\u003ctd\u003eHigher distance needed for the longer tube gap. Test with a retraction tower.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eZ offset\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eSlightly higher than PLA\u003c\/td\u003e\n\u003ctd\u003ePETG flows freely and \"lays down\" rather than being squeezed. If you see nozzle blobs or zits, raise Z offset by 0.02mm increments.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDrying (if needed)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e55–65°C for 6–8 hours\u003c\/td\u003e\n\u003ctd\u003ePETG is highly hygroscopic — moisture causes stringing, bubbling, and brittle layers. If you hear popping or see a foamy surface texture, dry before printing.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003eThe 3 Most Common PETG Problems — and How to Fix Them\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eStringing (thin plastic hairs between parts)\u003c\/strong\u003e\u003cbr\u003ePETG strings more than PLA because it's more viscous when molten and oozes during travel moves. Fix: lower nozzle temp 5°C, increase retraction slightly, enable \"Wipe Before Travel\" in your slicer, and dry the filament. Moisture is the most common hidden cause of unexpected stringing.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003ePrint bonding to the bed too aggressively\u003c\/strong\u003e\u003cbr\u003ePETG adheres very well — sometimes too well to glass or PEI. Fix: lower bed temp to 80°C, apply a thin layer of glue stick as a release agent, and always let the bed cool fully to room temperature before removing the print. Never pry PETG off a warm bed — you'll damage the surface.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eBubbles or foamy surface texture\u003c\/strong\u003e\u003cbr\u003eAlmost always wet filament. Fix: dry at 55–65°C for 6 hours before printing, then store in a sealed container with desiccant between sessions. PETG absorbs moisture faster than PLA or ABS — especially in humid climates.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eBulk Storage — Keeping 32 Spools Fresh\u003c\/h3\u003e\n\u003cp\u003eEvery spool ships vacuum-sealed with desiccant. Keep them sealed until you're ready to use them — they'll stay fresh for months in their original packaging. Once you break the seal on a spool:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eStore in an airtight container with fresh desiccant\u003c\/strong\u003e — a large bin with a silicone seal works well for 2–3 open spools at a time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUse a filament dry box while printing\u003c\/strong\u003e — especially in humid climates. PETG absorbs moisture quickly when left exposed on the printer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBatch consistency advantage:\u003c\/strong\u003e Ordering 32kg at once means all spools come from the same manufacturing batch. Color consistency across your entire production run — no shade drift between orders.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003eWho Is This 32-Pack For?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrint farms running multiple machines\u003c\/strong\u003e — 32kg covers weeks of continuous production at $13.49\/kg. The math is straightforward: fewer reorders, lower per-part cost, consistent color across your full catalog.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorkshops producing functional parts at volume\u003c\/strong\u003e — brackets, enclosures, outdoor fixtures, mechanical components — anywhere PETG's heat resistance and toughness outperform PLA at scale.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEtsy sellers and small product businesses\u003c\/strong\u003e printing batches of the same items across multiple colors. Pick your 32 most-used SKU colors and never run out of a variant mid-run.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMakerspaces and school labs\u003c\/strong\u003e that go through filament quickly and need a predictable stock of a reliable, student-safe material that's forgiving to print without enclosures or advanced setup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh-speed printer operators\u003c\/strong\u003e — Bambu Lab, Voron, RatRig, or any machine pushing 150mm\/s+ — who need a PETG formulation that keeps up with their hardware without stringing or adhesion failures.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eBrowse individual spools in our \u003ca href=\"\/collections\/petg-filament\"\u003ePETG Filament collection\u003c\/a\u003e. Explore everything in our \u003ca href=\"\/pages\/3d-printing-filaments\"\u003e3D Printing Filaments guide\u003c\/a\u003e.\u003c\/p\u003e","brand":"IIID MAX","offers":[{"title":"Default Title","offer_id":52840137621798,"sku":"PETG-PACK-32","price":431.68,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1004\/1986\/2822\/files\/PETG_PACK_32.webp?v=1772755513","url":"https:\/\/supplies3d.shop\/products\/32-x-1kg-high-speed-petg-filament-pack-1","provider":"SUPPLIES3D","version":"1.0","type":"link"}