{"product_id":"3-x-1kg-abs-filament-pack-1","title":"ABS Filament 3-Pack","description":"\u003ch2\u003e3kg of Heat-Resistant, Acetone-Smoothable ABS at $19.67\/kg | Mix Any 3 Colors\u003c\/h2\u003e\n\u003cp\u003eThree kilograms of ABS. Any three colors you want. Vacuum-sealed for freshness. Free shipping across the USA. At $19.67\/kg — 18% off the individual spool price — this is the smart way to stock your most-used ABS colors and never run out mid-project.\u003c\/p\u003e\n\u003cp\u003e⚠️ \u003cstrong\u003eBefore you order:\u003c\/strong\u003e ABS is not a beginner filament. It requires a \u003cstrong\u003eheated bed (90–110°C)\u003c\/strong\u003e, an \u003cstrong\u003eenclosed printer\u003c\/strong\u003e to prevent warping, and \u003cstrong\u003egood ventilation\u003c\/strong\u003e — ABS emits fumes during printing that you don't want to breathe in a small room. If you're set up for ABS, this is the best value way to keep three colors in rotation. If you're new to ABS, see the print settings and tips section below before you start.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eWhat Makes ABS the Go-To for Functional Parts\u003c\/h3\u003e\n\u003cp\u003eABS (Acrylonitrile Butadiene Styrene) is the same plastic used in LEGO bricks, car dashboards, and electronics enclosures. It's been the standard for functional 3D printing for decades for three reasons:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHeat resistance up to ~100°C\u003c\/strong\u003e — PLA softens in a hot car or near a heat source. ABS stays rigid where PLA fails. If your part lives in a warm environment — inside an electronics case, on an engine bay bracket, under direct sunlight — ABS is the right choice.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eImpact toughness\u003c\/strong\u003e — ABS bends before it breaks. PLA is harder but more brittle — it shatters under sudden impact. ABS absorbs the hit and flexes, which is why it's used in protective casings and structural brackets.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAcetone vapor smoothing\u003c\/strong\u003e — ABS dissolves in acetone. This means you can expose a finished ABS print to acetone vapor for a few minutes and the surface layers literally melt and reflow — eliminating layer lines and producing a glossy, injection-mold-quality finish. No sanding. No filler primer. Just chemistry.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003ch3\u003ePack Contents \u0026amp; Value Breakdown\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePack size\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e3 × 1kg spools (3kg total \/ 6.6 lbs)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eMaterial\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eABS (Acrylonitrile Butadiene Styrene)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFilament diameter\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e1.75mm ±0.02mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eColor selection\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eChoose any 3 colors from our ABS range\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrice per kg\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e$19.67 (vs $23.90 individual — 18% savings)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePackaging\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eVacuum-sealed with desiccant — each spool individually sealed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eShipping\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eFree across the USA\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003ePrint Settings for ABS\u003c\/h3\u003e\n\u003cp\u003eABS is less forgiving than PLA or PETG — small changes in temperature and environment have a big effect on results. Use these settings as your starting point and dial in from there.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSetting\u003c\/th\u003e\n\u003cth\u003eRecommended Range\u003c\/th\u003e\n\u003cth\u003eNotes\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eNozzle temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e230–250°C\u003c\/td\u003e\n\u003ctd\u003eStart at 240°C. Drop 5°C if you see stringing, raise 5°C if layers don't bond.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eBed temperature\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e90–110°C\u003c\/td\u003e\n\u003ctd\u003e100°C is the sweet spot for most setups. PEI sheet works best.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eEnclosure\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eStrongly recommended\u003c\/td\u003e\n\u003ctd\u003eTarget 40–50°C ambient inside. Without enclosure, large parts will warp. This is the #1 cause of failed ABS prints.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePart cooling fan\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003eOff or 0–10%\u003c\/td\u003e\n\u003ctd\u003eCooling air is the enemy of ABS layer adhesion. Keep it off. Never run full fan on ABS.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003ePrint speed\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e40–60mm\/s\u003c\/td\u003e\n\u003ctd\u003eSlower = better layer bonding and fewer warping issues.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eLayer height\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e0.2mm standard \/ 0.15mm for detail\u003c\/td\u003e\n\u003ctd\u003eThinner layers improve surface quality and reduce layer separation risk.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRetraction — Direct Drive\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e2–3mm at 30–50mm\/s\u003c\/td\u003e\n\u003ctd\u003eABS strings less than PETG — keep retraction moderate.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eRetraction — Bowden\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e4–6mm at 30–50mm\/s\u003c\/td\u003e\n\u003ctd\u003eHigher distance needed to compensate for the longer tube gap.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eFirst layer speed\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e15–20mm\/s\u003c\/td\u003e\n\u003ctd\u003eSlower first layer = better adhesion = fewer failures. Worth the extra time.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003cstrong\u003eDrying (if needed)\u003c\/strong\u003e\u003c\/td\u003e\n\u003ctd\u003e60–65°C for 4–6 hours\u003c\/td\u003e\n\u003ctd\u003ePopping sounds or rough surface? Moisture in the spool. Dry before printing.\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003chr\u003e\n\u003ch3\u003e3 ABS Printing Problems and How to Fix Them\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eWarping (corners lifting off the bed)\u003c\/strong\u003e\u003cbr\u003eThis is the most common ABS problem. Almost always caused by cold air hitting the part during printing. Fix: enclose the printer, raise bed temp to 100–110°C, add a brim in your slicer, and kill the cooling fan completely.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eLayer separation (print splitting horizontally)\u003c\/strong\u003e\u003cbr\u003eLayers aren't bonding because the part is cooling too fast between layers. Fix: raise nozzle temp 5–10°C, make sure enclosure is holding heat, and turn off the fan.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eStringing (thin hairs of plastic between parts)\u003c\/strong\u003e\u003cbr\u003eUsually means retraction is too short or temperature is too high. Fix: lower nozzle temp 5°C and increase retraction distance slightly. Run a retraction calibration tower if needed.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eAcetone Smoothing — How It Works\u003c\/h3\u003e\n\u003cp\u003eThis is ABS's secret weapon. Put a finished ABS print inside a sealed container with a small amount of acetone (nail polish remover). The acetone vapor — not the liquid — touches the surface and causes the outer layers to melt just slightly, reflow, and re-solidify smooth. The result is a glossy, professional finish with no visible layer lines. It takes about 5–10 minutes of exposure, then 30–60 minutes of drying. Works on any ABS color.\u003c\/p\u003e\n\u003cp\u003e⚠️ Do this outdoors or in a well-ventilated area. Acetone vapor is flammable — no open flames nearby.\u003c\/p\u003e\n\u003chr\u003e\n\u003ch3\u003eWho Is This 3-Pack For?\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEngineers and makers printing functional parts\u003c\/strong\u003e that will live in warm environments — under the hood, inside electronics, outdoors in summer — where PLA would deform.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePrototype builders who need smooth surfaces\u003c\/strong\u003e and don't want to spend hours sanding. The acetone vapor method turns a rough printed surface into a presentation-ready finish in under an hour.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorkshops and production users\u003c\/strong\u003e who go through ABS regularly and want to lock in the savings on their three most-used colors rather than paying per-spool pricing every time.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVoron, RatRig, and CoreXY builders\u003c\/strong\u003e — ABS is the standard material for Voron structural printed parts precisely because of its heat resistance and toughness. This pack covers a full printer's worth of parts plus spares.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003chr\u003e\n\u003cp\u003eBrowse individual spools in our \u003ca href=\"\/collections\/abs-filament\"\u003eABS Filament collection\u003c\/a\u003e. Explore everything in our \u003ca href=\"\/pages\/3d-printing-filaments\"\u003e3D Printing Filaments guide\u003c\/a\u003e.\u003c\/p\u003e","brand":"IIID MAX","offers":[{"title":"Default Title","offer_id":52840001831206,"sku":"ABS-PACK-3","price":59.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1004\/1986\/2822\/files\/ABS_Filament_PACK_3_IIIDMAX.webp?v=1773069040","url":"https:\/\/supplies3d.shop\/products\/3-x-1kg-abs-filament-pack-1","provider":"SUPPLIES3D","version":"1.0","type":"link"}